Data Element list used by SAP ABAP Table MCQAQR_KYF (Comm. structure: Inspection results - key figures)
SAP ABAP Table 
MCQAQR_KYF (Comm. structure: Inspection results - key figures) is using
| # | Object Type | Object Name | Object Description | Note |
|---|---|---|---|---|
 |
|
|||
| 1 |  Data Element |
QANTEIL | Estimated Fraction of Nonconforming Sample Units | |
| 2 | Data Element |
QANTEILO | Estimated Fraction Above the Tolerance Range | |
| 3 | Data Element |
QANTEILU | Estimated Fraction Below the Tolerance Range | |
| 4 | Data Element |
QANZFEHEH4 | Number of Nonconforming Sample Units | |
| 5 | Data Element |
QANZFEHL4 | Number of Defects Found | |
| 6 | Data Element |
QANZWERTG4 | Number of Inspected Sample Units | |
| 7 | Data Element |
QANZWERTO4 | Number of Measured Values Above the Tolerance Range | |
| 8 | Data Element |
QANZWERTU4 | Number of Measured Values Below the Tolerance Range | |
| 9 | Data Element |
QBWGRENZOB1NI | Additional first upper limit value exists | |
| 10 | Data Element |
QBWGRENZOB2NI | Additional 2nd upper limit exists | |
| 11 | Data Element |
QBWGRENZUN1NI | Additional 1st lower limit exists | |
| 12 | Data Element |
QBWGRENZUN2NI | Additional 2nd lower limit exists | |
| 13 | Data Element |
QBWSOLLWNI | Target value exists | |
| 14 | Data Element |
QBWTOLOBNI | Upper Tolerance Limit Exists | |
| 15 | Data Element |
QBWTOLUNNI | Lower Tolerance Limit Exists | |
| 16 | Data Element |
QCP | Process Capability Index (Cp Value) | |
| 17 | Data Element |
QCPK | Process Capability Index (Cpk Value) | |
| 18 | Data Element |
QGRENZOB1 | First Upper Specification Limit | |
| 19 | Data Element |
QGRENZOB2 | Second Upper Specification Limit | |
| 20 | Data Element |
QGRENZUN1 | First Lower Specification Limit | |
| 21 | Data Element |
QGRENZUN2 | Second Lower Specification Limit | |
| 22 | Data Element |
QMASSEH | Unit of Measurement, in Which Quantitative Data Is Stored | |
| 23 | Data Element |
QMISMITTEL | Mean Value | |
| 24 | Data Element |
QMISSTD | Standard Deviation | |
| 25 | Data Element |
QMITTELWRT | Arithmetic Mean of Valid Measured Values | |
| 26 | Data Element |
QMKCONTROL | Cntrl Indicator String for Insp. Char./Master Insp. Char. | |
| 27 | Data Element |
QNIANTEIL | Not Initialized for Fraction | |
| 28 | Data Element |
QNINITIAL | Value Not Initial if Set | |
| 29 | Data Element |
QSOLLWERTE | Target Value for a Quantitative Characteristic | |
| 30 | Data Element |
QSTELLEN | Number of Places to the Right of a Decimal Point (Accuracy) | |
| 31 | Data Element |
QSTELLEN | Number of Places to the Right of a Decimal Point (Accuracy) | |
| 32 | Data Element |
QSTELLEN | Number of Places to the Right of a Decimal Point (Accuracy) | |
| 33 | Data Element |
QSTELLEN | Number of Places to the Right of a Decimal Point (Accuracy) | |
| 34 | Data Element |
QSUMEW | Total of Valid Single Values | |
| 35 | Data Element |
QSUMFANT | Total Nonconforming Shares | |
| 36 | Data Element |
QSUMFEHLEH | Total of Nonconforming Units | |
| 37 | Data Element |
QSUMMW | Total of Mean Values | |
| 38 | Data Element |
QSUMSIGMASTP | Total of Sample Dispersions | |
| 39 | Data Element |
QSUMVAR | Total of Sample Variances | |
| 40 | Data Element |
QSUMVARIN | Total of Single Value Variances | |
| 41 | Data Element |
QTOLOB | Upper Specification Limit | |
| 42 | Data Element |
QTOLUN | Lower Tolerance Limit | |
| 43 | Data Element |
QTSTICHPRO | Partial Samples Possible | |
| 44 | Data Element |
QZHLNA | Number of Accepted Samples | |
| 45 | Data Element |
QZHLNHF | No. of Samples with Major Defect as Defect Class | |
| 46 | Data Element |
QZHLNKF | No. of Samples with Critical Defect as Defect Class | |
| 47 | Data Element |
QZHLNNF | Number of Samples with Minor Defect as Defect Class | |
| 48 | Data Element |
QZHLNR | Number of Rejected Samples | |
| 49 | Data Element |
QZHLNSKIP | Number of Skipped Samples | |
| 50 | Data Element |
QZHLNSTAT | Number of Valid Single Values | |
| 51 | Data Element |
QZHLNSTPF | Sample Size (No. of Valid Values in Sample) |
