Data Element list used by SAP ABAP Table MC05Q2_0INSP (QM-BW Extraction: Inspection Char. Results (Quantitative))
SAP ABAP Table 
MC05Q2_0INSP (QM-BW Extraction: Inspection Char. Results (Quantitative)) is using
| # | Object Type | Object Name | Object Description | Note |
|---|---|---|---|---|
 |
|
|||
| 1 |  Data Element |
CHARG_D | Batch Number | |
| 2 | Data Element |
ELIFN | Vendor's account number | |
| 3 | Data Element |
MATNR | Material Number | |
| 4 | Data Element |
PLNKN | Number of the task list node | |
| 5 | Data Element |
PLNNR | Key for Task List Group | |
| 6 | Data Element |
PLNTY | Task List Type | |
| 7 | Data Element |
QANTEIL | Estimated Fraction of Nonconforming Sample Units | |
| 8 | Data Element |
QANZFEHEH4 | Number of Nonconforming Sample Units | |
| 9 | Data Element |
QANZFEHL4 | Number of Defects Found | |
| 10 | Data Element |
QANZWERTG4 | Number of Inspected Sample Units | |
| 11 | Data Element |
QANZWERTO4 | Number of Measured Values Above the Tolerance Range | |
| 12 | Data Element |
QANZWERTU4 | Number of Measured Values Below the Tolerance Range | |
| 13 | Data Element |
QATTRIBUT | Attribute of the Results Record (Valid, Invalid,...) | |
| 14 | Data Element |
QBWSOLLWNI | Target value exists | |
| 15 | Data Element |
QBWTOLOBNI | Upper Tolerance Limit Exists | |
| 16 | Data Element |
QBWTOLUNNI | Lower Tolerance Limit Exists | |
| 17 | Data Element |
QHERK | Inspection Lot Origin | |
| 18 | Data Element |
QKUNWE | Customer (Ship-To Party) | |
| 19 | Data Element |
QLFNKN | Current Node Number from Order Counter APLZL | |
| 20 | Data Element |
QMASSEH | Unit of Measurement, in Which Quantitative Data Is Stored | |
| 21 | Data Element |
QMERKNR | Master Inspection Characteristics | |
| 22 | Data Element |
QMERKNRP | Inspection Characteristic Number | |
| 23 | Data Element |
QPART | Inspection Type | |
| 24 | Data Element |
QPHYSPRNR | Physical Sample Number | |
| 25 | Data Element |
QPLOS | Inspection Lot Number | |
| 26 | Data Element |
QPMETHODE | Inspection Method | |
| 27 | Data Element |
QPROBENRPP | Sample Number (Based on an Inspection Point) | |
| 28 | Data Element |
QPRPLATZ | Work Center | |
| 29 | Data Element |
QPRUEFDATV | Inspection Start Date | |
| 30 | Data Element |
QSOLLWERTE | Target Value for a Quantitative Characteristic | |
| 31 | Data Element |
QSUMEW | Total of Valid Single Values | |
| 32 | Data Element |
QSUMEW2 | Sum of Squares of Valid Single Values | |
| 33 | Data Element |
QSUMMW | Total of Mean Values | |
| 34 | Data Element |
QSUMSIGMASTP | Total of Sample Dispersions | |
| 35 | Data Element |
QSUMVAR | Total of Sample Variances | |
| 36 | Data Element |
QSUMVARIN | Total of Single Value Variances | |
| 37 | Data Element |
QTLOS | Partial lot number | |
| 38 | Data Element |
QTOLOB | Upper Specification Limit | |
| 39 | Data Element |
QTOLUN | Lower Tolerance Limit | |
| 40 | Data Element |
QVERSNRPM | Version Number of the Inspection Method | |
| 41 | Data Element |
QZAEHLER | Plant for the Master Inspection Characteristic | |
| 42 | Data Element |
QZHLNA | Number of Accepted Samples | |
| 43 | Data Element |
QZHLNR | Number of Rejected Samples | |
| 44 | Data Element |
QZHLNSTAT | Number of Valid Single Values | |
| 45 | Data Element |
QZHLNSTPF | Sample Size (No. of Valid Values in Sample) | |
| 46 | Data Element |
ROCANCEL | Indicator: Cancel Data Record | |
| 47 | Data Element |
WERKARBPL | Plant/Work Center | |
| 48 | Data Element |
WERKS_D | Plant | |
| 49 | Data Element |
WERKS_D | Plant |
