Message Number list used by SAP ABAP Program LEA79F01 (Include LEA79F01)
SAP ABAP Program LEA79F01 (Include LEA79F01) is using
# Object Type Object Name Object Description Note
     
1 Message Number  AH - 596 Round. rules for Wobbe factor only req. for correcting gas law dev.factor
2 Message Number  AH - 184 From-nominal load is zero
3 Message Number  AH - 185 To-nominal load is zero
4 Message Number  AH - 186 From-measured pressure is zero
5 Message Number  AH - 187 To-measured pressure is zero
6 Message Number  AH - 468 Maintain weighting key for averaging type "weighted average"
7 Message Number  AH - 469 Maintain weighting key for air pressure "weighted average"
8 Message Number  AH - 470 Enter weighting key only for weighted calculation of average
9 Message Number  AH - 527 Transport entry created for volume correction factor procedure &1
10 Message Number  AH - 595 Rounding &1 is larger than &2
11 Message Number  AH - 063 Enter a billing class
12 Message Number  AH - 599 Billing class &1 does not match billing class &2 gas procedure &3
13 Message Number  AH - 806 Enter standard temperature/zero temperature
14 Message Number  AH - 807 Not possible to maintain standard temperature/zero temperature
15 Message Number  AH - 817 Weighting key &1 division cat. &2: energy feeding table incomplete
16 Message Number  AH - 818 Enter gas pressure correction only for gas pressure determination
17 Message Number  AH - 825 Only gas pr. correctn can be maintained for GPr. determ. using GPr. area
18 Message Number  AH - 840 Enter standard pressure
19 Message Number  AH - 858 Enter replacement VCF procedure for register relationship ZZ only
20 Message Number  AH - 859 Replacement vol. corr. factor proc. is required for reg. relationship ZZ
21 Message Number  AH - 094 Maintain temperature component
22 Message Number  AH - 095 Special proc. "no temperature" only necessary for thermal gas billing 00
23 Message Number  AH - 019 To-measured pressure &1 is less than from-measured pressure &2
24 Message Number  AH - 068 Volume correction factor procedure &1 not in table &2
25 Message Number  AH - 070 Volume correction factor procedure &1 is still used (see where-used list)
26 Message Number  AH - 073 Measured pressure &1 is larger than permitted maximum value &2
27 Message Number  AH - 074 From-nominal load &1 greater than to-nominal load &2
28 Message Number  AH - 075 No entries for billing class &1 in table &2
29 Message Number  AH - 077 Please also maintain gas law deviation factor after correcting GLD factor
30 Message Number  AH - 078 Only enter air pressure (corr.) if thermal gas billing = 00 or 01
31 Message Number  AH - 080 Enter either fixed temperature or averaging type/average from
32 Message Number  AH - 081 Enter both "averaging type" and "average from"
33 Message Number  AH - 082 Enter all rounding attributes
34 Message Number  AH - 083 Normal air pressure &1 deviates from standard value &2
35 Message Number  AH - 085 No gas law deviation factor correction is possible for factor 01
36 Message Number  AH - 091 Only choose usage type if "fixed volume correction factor" is used
37 Message Number  AH - 092 General control indicators are partially ignored in special procedure
38 Message Number  AH - 093 Gas law deviation factor 01 only possible for temp./pressure billing
39 Message Number  AH - 079 Only enter averaging type/avg from/fixed temp.if thermal gas billing = 00
40 Message Number  AJ - 436 Enter a PrTempR-JT key to calculate J-T effect
41 Message Number  AJ - 437 Only enter PrTempR-JT key if J-T effect is to be calculated
42 Message Number  AJ - 445 Special procedures are not permitted for temperature or pressure extra
43 Message Number  AJ - 461 Joule-Thomson effect is only possible with thermal gas billing 00
44 Message Number  AJ - 469 The last value does not match the one in the &1 calorific value procedure
45 Message Number  AJ - 393 Joule-Thomson indicator cannot be used yet
46 Message Number  AJ - 471 'Last value' cannot be combined with proration or calculation of average
47 Message Number  AJ - 510 Choose only one volume correction factor access when using VCF from reg.
48 Message Number  AJ - 512 Cannot maintain MeasPrPror/GasPrDeterm/GasPrCorr for thermal gas bill. &1
49 Message Number  AJ - 513 Not possible to take JT effect into account for thermal gas billing 03
50 Message Number  AJ - 514 Joule-Thompson effect is not taken into account for special procedures
51 Message Number  AJ - 516 Spec. proc. for register rel. ZZ: compressibility only possible by device
52 Message Number  AJ - 660 You can only combine to-the-day air pressure with the daily procedure
53 Message Number  AJ - 434 Choose additional pressure calculation to take J-T effect into account
54 Message Number  AJ - 185 Only possible to calculate average using billing period
55 Message Number  AJ - 186 Weighting key &1 not permissible with weighting procedure &2
56 Message Number  AJ - 236 Not possible to correct gas law deviation factor for GL dev. factor 03
57 Message Number  AJ - 237 Gas law deviation factor 03 is only possible for temp./pressure billing
58 Message Number  AJ - 373 "Temperature extra" indic. only poss. for thermal gas billing 01 and 02
59 Message Number  AJ - 374 "Pressure extra" indicator only possible for thermal gas billing 02
60 Message Number  AJ - 377 Can only choose "Temp. extra" with "Press. extra" (for ther. gas bill.02)
61 Message Number  AJ - 418 In spec. procedure ZE you cannot enter determ. of GLDF and corr. of GLDF
62 Message Number  AJ - 429 Do not suppress temperature calculation when Joule-Thomson effect is used
63 Message Number  AJ - 433 Choose additional temperature calculation to take J-T effect into account
64 Message Number  AJ - 435 Choose GasPr.det. to take J-T effect into account
65 Message Number  E9 - 002 &1 &2 &3 &4 has been changed
66 Message Number  E9 - 004 &1 &2 &3 &4 has been created
67 Message Number  E9 - 011 &1 &2 &3 &4 does not exist
68 Message Number  E9 - 013 No changes were made
69 Message Number  E9 - 031 &1 &2 &3 &4 has been deleted
70 Message Number  E9 - 100 You have no authorization for &2 &1
71 Message Number  E9 - 103 You have no change authorization; &1 will be displayed
72 Message Number  E9 - 887 Internal error: Unexpected exception &2 in calling up function module &1